Articles in this section

NPR Piston Rings & Valve Guides — Sizing and Ordering

NPR is a piston ring and valve guide brand that Win Auto Parts imports for the trade. The range is deliberately small — 7 active part numbers — so treat it as a specific range to check rather than a general catalogue. If the reference you need is not in it, ask the trade desk which other ring brands we hold for that engine.NPR သည် Win Auto Parts မှ တင်သွင်းသော piston ring နှင့် valve guide အမှတ်တံဆိပ် ဖြစ်သည်။ ပစ္စည်း ၇ မျိုးသာ ရှိသဖြင့် နည်းပါသည်။ လိုအပ်သည့် နံပါတ် မပါဝင်ပါက အခြား အမှတ်တံဆိပ်များကို ကောင်တာတွင် မေးပါ။

What does the NPR range cover?

These are live counts of active part numbers in stock control, not a target:အောက်ပါတို့သည် လက်ရှိ ရှိနေသော ပစ္စည်း အရေအတွက် အမှန် ဖြစ်ပါသည်။

Part type Active part numbers
Piston ring sets 5
Valve guides 2

What you must know before ordering a ring set

A piston ring set is sized to the bore, so the order needs the engine code and the bore size including any oversize from a rebore. Standard, 0.25, 0.50 and so on are different part numbers, not different packaging, and a standard set will not seal a rebored block. Measure the bore after machining and order to the measurement, never to what the engine had originally.Piston ring set ကို bore အရွယ်အစားအလိုက် ရောင်းသည်။ ထို့ကြောင့် အင်ဂျင်ကုဒ် နှင့် bore အရွယ်အစား (ချဲ့ပြီးသား ဖြစ်ပါက oversize အပါအဝင်) လိုအပ်ပါသည်။ Standard၊ 0.25၊ 0.50 တို့သည် နံပါတ် မတူပါ။ ချေပြီးမှ တိုင်း၍ မှာယူပါ။

Also say how many cylinders you are ordering for, because some references are sold per cylinder and some as a full engine set. A four-cylinder engine supplied with a single-cylinder set is the most common ordering error on this range.Cylinder မည်မျှအတွက် မှာယူသည်ကိုလည်း ပြောပါ — အချို့သည် cylinder တစ်လုံးစီ၊ အချို့မှာ အင်ဂျင်တစ်လုံးစာ ဖြစ်သည်။ ၎င်းသည် အများဆုံး မှားတတ်သော အချက် ဖြစ်သည်။

What should be checked when fitting rings?

Check the end gap of every ring in the bore it will run in, at the specified depth, against the manufacturer’s figure — gaps that are too small will butt and scuff the bore when hot, and too large will not seal. Fit the rings the right way up: most compression rings have a marking that faces the crown, and fitting one inverted will burn oil from the first mile. Stagger the ring gaps around the piston as specified, and use a proper ring compressor rather than forcing the piston in.Ring တစ်ခုချင်းစီ၏ end gap ကို သက်ဆိုင်ရာ bore အတွင်း သတ်မှတ် အနက်တွင် တိုင်းစစ်ပါ — gap နည်းပါက ပူချိန် bore ကို ခြစ်မိပြီး များပါက မပိတ်ပါ။ Ring ကို မှန်ကန်သော ဘက်ဖြင့် တပ်ပါ — အမှတ်အသားသည် piston ထိပ်ဘက်သို့ မျက်နှာမူရမည်။ Gap များကို သတ်မှတ်အတိုင်း ခွဲထားပြီး ring compressor သုံးပါ။

For valve guides, the guide is fitted and then reamed to the valve stem, and the stem seal and valve seat both depend on the guide being concentric. Check stem-to-guide clearance against specification after reaming rather than assuming the ream size was correct.Valve guide ကို တပ်ပြီးမှ valve stem နှင့် ကိုက်ညီအောင် ream လုပ်ရသည်။ Ream ပြီးနောက် stem-to-guide clearance ကို သတ်မှတ်ချက်နှင့် နှိုင်းယှဉ် စစ်ဆေးပါ။

Diagram — end gap, orientation, stagger

Three panels on fitting piston rings: measuring the end gap in the bore the ring will run in, fitting the ring with its mark facing the piston crown rather than inverted, and staggering the ring gaps around the piston. A note explains that standard and oversize are different part numbers.

Three checks decide whether a ring set seals. The end gap is measured in the bore the ring will actually run in; the mark faces the crown, because a ring fitted upside down burns oil from the first mile; and the gaps are staggered rather than lined up with each other.အချက် သုံးချက်က ring set ပိတ်မပိတ် ဆုံးဖြတ်သည်။ End gap ကို သက်ဆိုင်ရာ bore အတွင်း တိုင်းပါ။ အမှတ်အသားသည် piston ထိပ်သို့ မျက်နှာမူရမည် — ပြောင်းပြန် တပ်ပါက ဆီလောင်ပါသည်။ Gap များကို ခွဲထားပါ။

Where do you buy it?

Win Auto Parts is a trade counter, not a retail shop, and it operates from one location in Yangon. Orders go through the trade desk by phone, by email or through this support portal. Trade and wholesale enquiries go to winautoparts.com; retail customers are served by winstores.com.Win Auto Parts သည် ရန်ကုန်တွင် တည်နေရာ တစ်ခုတည်း ရှိသော ကုန်သွယ်မှု (B2B) ကောင်တာ ဖြစ်ပြီး လက်လီဆိုင် မဟုတ်ပါ။ လက်ကား အတွက် winautoparts.com၊ လက်လီ အတွက် winstores.com ဖြစ်ပါသည်။

Related Articles

Win Auto Parts is a trading name of Win Store Co., Ltd. (DICA 119730635).

Contact Win Auto Parts — Trade Enquiries

Phone: 09 5105768  ·  winautoparts.com  ·  support.winautoparts.com

Industrial Zone 1, South Dagon Township, Yangon, Myanmar  ·  Monday to Saturday, 9 AM – 6 PM

 

 

ORDER & ENQUIRIES
မှာယူရန် နှင့် စုံစမ်းရန်

Phone  09 5105768  |  Email  support@winautoparts.com

Online  winautoparts.com  |  support.winautoparts.com (support portal and web chat)

South Dagon Distribution Centre  (172/173/174) Mawlamyine Street, Industrial Zone 1, South Dagon Township, Yangon — Mon–Sat 8:30 AM – 5:30 PM

Thakaytha Distribution Centre  Thakaytha Industrial Zone, Yangon — Mon–Sat 9:00 AM – 6:00 PM

Was this article helpful?
0 out of 0 found this helpful

Comments

0 comments

Article is closed for comments.